How To Make A Homemade Water Bong

Next take your pen with the ball point end still intact and push it through the hole to make it bigger. You can make your own out of a water bottle using a few simple tools.

Pin On Crafty

Lets make a perfect homemade bongForemost hold the plastic bottle in your hand and with your pen poke a hole in the bottle near its neck to make a carb.

How to make a homemade water bong. Scoop out the seeds. Remove the cap on top of the bottle and it will act as your mouthpiece. It should be approximately.

After making a carb poke another but bigger hole in the bottle in its middle to penetrate the stem or a pen pipe into it. If you want to smoke out of a bong but you dont have one around dont fret. Cut a hole around the stem and remove the plug Keep this piece as youre going to need it again at the end.

You will want to use a bottle that is just the right size for bong-making purposes. You will not need it. If you want a full in-depth explanation with photos for how this is done read this.

Stick a downstem in the hole or use a pen if you dont have one available. Making a Basic Water Bottle Bong 1. Now that you have youve literally created a bong just add water filling the bottle about a quarter of the way.

Tear off a small piece of aluminum foil. Then remove the bowl and inhale as you. How to Make your Water Bong.

Any kind of plastic bottle will work but keep in mind that the. Water Bong - 1. Luckily making this homemade bong is easy as 1-2-3even if youre hella stoned.

Then heat the top of the hook until its white-hot and push it right there the bottle where you want the carb to be. You can make your own out of a water bottle using a few simple tools. We suggest salting and baking those bad boys for a tasty.

One very solid method is to take a wire coat hanger and straighten out the hook. A standard 169 ounce. Take the pen apart keeping the barrel Poke the pen barrel into the hole youve just made placing it at an angle so it points down to the bottom of the bottle inside and up towards you on the outside.

How to make a homemade water bong. If youre looking for cute bongs or expensive bongs then a homemade bong probably isnt for you dude. Poke Holes In Your Water Bottle With the pin or needle poke a hole toward the top of your water bottle of choice.

Knowing how to make a water bottle bong is sure to come in handy on countless occasions and it couldnt be easier. The water bottle bong is another classic that is quick and easy to make. You will want to use a bottle that is just the right size for bong-making purposes.

Make a second hole slightly. Before you do anything to your water-bottle construct what will become the shaft of your bong. Just uh youre.

This piece will serve as the bowl. A bong made out of plastic and other materials found around the house. Making a Plastic Bottle Bong 1.

Cut the plastic bottle in half and place the upper half into the larger container. How to make a water bottle bong. Light your weed and slowly lift the bottle out of the container which will fill the bottle with smoke.

Poke a hole just below the neck of the water bottle to make the carb. Heres an alternate method. See more ideas about diy bong bongs homemade bong.

DIY a fresh new bong out of something you already have laying around diybong marijuana cannabis Maryjane weed 420howto diy420. You can also use a nail a screw or any other easily manipulated piece of metal that you can heat up and push through the back of the bong. This will be your carb hole.

We recommend one you can hold in the palm of your hand without too much problem. For a bowl you can use a metal bolt or the nib of a pen if you dont have a spare bowl. But if youre creative and in need of getting stoned right away then heres how to make a bong out of a water bottle.

Find a small pumpkin. Oct 13 2019 - Cant get to the Head Shop. The carb is the hole youll cover with your.

Take your scissors or knife and cut a small hole just below the neck Take a plastic bottle of your choice and fill it ¼ full with water. Take an empty clean plastic bottle poke a hole about halfway up the bottle on the side. Take a bucket or container that is bigger than the plastic bottle and fill the container with water.

Making a Basic Water Bottle Bong. Take a knife or a pair of scissors and cut a small hole in the back of the bong either at the top or bottom and youre all set. Using the scissors make a hole in the bottle about 4 from the bottom.

Add marijuana to the bowl and you are good to go just light and inhale. Take a plastic bottle of your choice and fill it ¼ full with water. Fill up a plastic bottle ¼ of the way with water.

For a grommet you can use a rubber washer or either modeling clay or electrical tape if you dont have one available. To do this youre just going to make a pen-pipe.

Pin On All Things Mary Jane